Welcome to Chassis Engineering. This is where we will offer our final inventory.
Check back often as we will continue to add to this list. In time, we will begin to add equipment, tools, etc. as well as automotive treasures.
Remember : All sales are "AS-IS" and "FINAL".

AS-0106 Channel Frame Universal Frame Adapter

$19.00
(2 reviews) Write a Review
SKU:
AS-0106
Channel Frame Universal Frame Adapter

 swapmeet-copy.png

Please note, All Swap Meet Sales "AS-IS" and "FINAL"

 

Chassis Engineering AS-0106 comes as a pair of universal frame adapters for Channel-style frames with a frame width ranging from 20" to 25".

channel-frame.jpg

These frame adapters are adjustable, and can be cut to the length you need to make them match up with the mounts of your engine. 

as-0106.jpg

After cutting them to the needed length, weld the adapters to the mounting bracket and then bolt them to your frame.

 

For best results, have a look at our engine mounts selection to find a matching set of mounts for your particular engine, and use our streetrod-engineered SS-0011 engine cushion set with Thru Bolt Construction for safety, stability and durability.

SS-0011 Universal Engine Cushion Set

For some tips on engine mounting, have a look at our Common Sense Engine Mounts blog post, located here, and our One Technique for Engine Swapping blog post, located here. Both posts go into some detail on what comes into play when swapping/installing an engine, and should help in doing it right the first time.


Don't reinvent the wheel!

 

We have a large collection of complete engine mount kits for various car models. Before going the universal route, have a look at our collection here, link, and see if there is a swap kit for your car listed. If there is, use that kit instead.

If you can't find a kit for your particular car frame and engine combo, you can use the steps below to determine which parts you need.

 

Each engine mounting kit is made up of 3 parts:

 engine-mounting.jpg

1a. Frame adapters (link).

Channel Frame Universal Frame Adapter

 

Our universal frame adapters come in different styles.

 

  • For  channel-frame-small.jpg channel frames use AS-0106 (linkas-0106-small.jpg .
  • For  boxed-frame-small.jpg boxed frames use AS-0304 (linkas-0304-small.jpg or our most popular  AS-0305 (link) as-0305-small.jpg , which is available in 4 lengths.
  • For  top-hat-frame-chevy-small.jpg top hat frames (1936-1954 Chevy cars) use AS-0204 (link) as-0204-small.jpg

 

All of our universal frame adapters are adjustable and can be cut to the length needed to properly align the frame mounts with the engine mounts.

To determine the length of the frame adapters, use the information below to determine the frame width and the engine mount width:

  • If you are using a boxed-type frame, measure the distance on the inside of the frame between the boxing plates.
  • If you are using a channel-type frame, measure the distance on the inside of the frame between the side walls of the frame rails.

box-frame.jpg channel-frame.jpg

if you are using existing engine mounts, measure between the center points of the engine block mounting points, otherwise use the chart below to determine the width of the mounts you need.

frame-width-engine-mount-length.jpg

Then simply substract the engine mount width from the frame width and divide it by two (for a frame adapter on each side of the frame).

Example:

We have a frame of 23 inches wide. According to the chart, we would use 19" engine mounts.

23 inches minus 19 inches leaves us with 4 inches, so the frame adapters would need to be (4 divided by 2) 2 inches long (from the edge to the center of the mounting hole).

engine-mounting-example-measurements.jpg

 

Again, before you go the universal route, check and see if we have a full kit for your car and engine combination listed (link). If we do, it will save you some fabrication work.

 

1b. Engine Crossmembers (link) for use with wide frames.

Weld-On Engine Crossmember 8 inch Drop

For cars with a wide (26 inch or more) frame, we have engine crossmembers available, link.

We offer crossmembers with various drops. To determine which one would work best with your setup, locate the center line between the 2  engine mounts and place a flat strap across the bottom of the oil pan at this point. Then measure from here to the center of the crank shaft. This distance corresponds to the drop listed for the crossmember. Note: allow at least an extra 1/2 inch of clearance between the oil pan and the crossmember.

If you use our 19 inch engine mounts, our engine crossmembers can be used with any engine.

 

2. Engine mounts (link).

CS-1119

We offer engine mounts for a large variety of engines, in a number of different lengths to make them work with just about any frame type. 

The engine mount style is chosen based on the type (brand/model) of engine, and the engine mount length is determined by the width of the frame.

 

  • For boxed frames, measure the distance on the inside of the frame between the boxing plates:

box-frame.jpg

  • For channel frames, measure the distance on the inside of the frame between the side walls of the frame rails.

channel-frame.jpg

 

To determine the length for the engine mount, measure between the center points of the engine block mounting points. Then use the information below to determine the length you need.

frame-width-engine-mount-length.jpg 

Note: If you are using one of our engine crossmembers instead of our frame adapters, use 19 inch engine mounts.

 

3. Engine Mount Cushion Set (link).

SS-0011 Universal Engine Cushion Set

For all the Chassis Engineering Engine Mounting Kits we use our biscuit style, streetrod-engineered SS-0011 engine cushion set (link).

This cushion set is impervious to gas and oil and offers great shock- and sound absorption as well as increased resistance to deformation and temperature extremes. It uses Thru Bolt Construction for safety and stability with a larger cross section to support even heavier engines.

universal-engine-mounting.jpg

2 Reviews Hide Reviews Show Reviews

  • 5
    Universal channel frame adapter

    Posted by Unknown on 17th Oct 2017

    Adapters where as expected. Plenty of material to adjust for custom applications

  • 5
    They work great.

    Posted by David B on 24th Jul 2017

    This is the second time I've used your parallel leaf spring mounts. They work great.
    The front and rear sway bars fit as advertised.
    The early hemi engine mounts and frame adapters are well engineered and work correctly. This also is a product I've used before.
    I bought my first set of parallel leaf spring mounts about 1980 or 81.. As I remember it, at that time you had to go to the junk yard and get springs from a Dodge van. Any way, I've always been satisfied with your products.